Search Parts
Starts With
Ends With
Contains
Exact Match
 

Application Notes
Category
ID Description
Design Information
ANI-006 M/A Com Synthesizer Evaluation Kit Software (zip file)
Field Effect Transistors in Theory and Practice (supplied with the permission of Motorola.)
RF Small Signal Design Using Two-Port Parameters (supplied with the permission of Motorola)
Impedance Matching Networks Applied to RF Power Transistors (supplied with the permission of Motorola)
Ceramic Surface Mount Amplifiers
GPS Consideration for Automotive Applications
Printed Circuit Board Design for LSM1 VCO's
Programming Guide Integer N PLL Synthesizer 35 - 1100 MHz
Programming Guide Integer N PLL Synthesizer 35 - 2500 MHz
Techniques to Achieve High Isolation with GaAs MMIC Switch Chips
Positive Voltage Control of GaAs MMIC Control Devices
Suggested Circuit Controller for a Dual-Control FET VVA in AGC Temp Comp
Drivers for GaAs FET MMIC Switches and Digital Attenuators
Electrical Characterizations of Packages for use with GaAs MMIC Amplifiers
RF Directional Couplers and 3dB Hybrids Overview
Power Dividers / Combiners
RF Balun Transformers
RF Hybrid Devices
Selection of Antenna and Cable for Optimum Automotive GPS Performance
CATV Terms and Terminologies
Optimizing AT65-0009 for Communication Bandwidths
The Choice of Polarization - Indoor Picocell Antennas
Drivers for GaAs FET Switches and Digital Attenuators
Designing with PIN Diodes
GaAs MMIC Low Noise Amplifiers (SOIC-8 Platform)
PIN Diode Vector Modulators - Fundamentals and Drive Requirements
GaAs MMIC Based Control Components with Integral Drivers
Using the DR65-0109 (DR65-0003 replacement part) to Drive SPDT PIN Switches
An Examination of Recovery Time of an Integrated Limiter/LNA (IEEE Microwave Magazine 3/04)
S-Parameter S2P File Format Guide
Intermodulation Distortion (IMD) Testing of Ferrite Circulators and Isolators
Synthesizer Evaluation Board Application Note
Maximum Peak Power of Ferrite Junctions
Discusses base plate temperature for M/A-COM circulators / isolators products and the choice for base plate materials and their impact on the power handling capability
AN3027 What actually creates the 90 degree coupler phase shift?
ESD Protection of Broadband GaAs CATV and FTTx Amplifiers
Product Information

  AN3025

Transistor Mounting and Solderability

  AN001

Microwave Power Transistor Impedence Measurement
Reflow Soldering Conditions for VCO and Synthesizer Products
Tape and Reel Packaging for LSM1A VCO's
Tape and Reel Packaging for LSM2 VCO's
Tape and Reel Packaging for Surface Mount Components
High Volume Commercial Plastic Packaged GaAs Monolithic Devices
Surface Mounting Instructions - Footprint Guidelines
Bonding, Handling and Procedures for Chip Diode Devices
CR-15 Packaging Handling and Mounting Procedures
Bonding, Handling, and Mounting Procedures for Millimeterwave PHEMT MMIC's
Installation and Application Information for Dual Directional Coupler with Lightning
Surface Mounting Instructions CR-9, 11, 12, 13, 14 Ceramic 16 and 24 PIN Packages
Surface Mounting Instructions for PQFN Packages
ESD/EOS Protection for GaAs MMIC Switches
C2083 Application Note is replaced by S2083
Deploying M/A-COM VCOs: Buffering, Mounting and Power Supplies
MA06000 Frequency Selection
Electrical Characterization of MAAMSS0031 CATV Amplifier at +5 Volts and Reduced Gain
Electrical Characterization of the MAAMSS0031, 16 dB Gain Application Circuit

  AN3016

Procedure for Handling GaAs MSAG MMICs

  AN3017

Procedure for MSAG MMIC AuSn Eutectic Solderability

  AN3018

Known Good Die Delivery Specification

  AN3019

Procedure for Thermal Management of Very High Power GaAs MMICs in Fixtures

  AN-010

Reflow Soldering Guidelines for RoHS Compliant E-Series Surface Mount Components

  AN3021

Selection of M/A-COM PIN Diodes for Microwave Switch Designs

Quality Information
Moisture Effects on the Soldering of Plastic Encapsulated Devices

 

  © Copyright/Privacy Statement